Check Us Out

 

 

What are your ideas with regards to How to Install a Bathtub Yourself?

Installing a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily available, the task can relocate easily; if you need to open up a wall to remove the old tub and place the brand-new tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the new one. Ensure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your bathroom if you have already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipes have been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub till the level reviews degree.
To set up taps, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Turn on the supply of water as well as check all joints and new pipework for leakages and also tighten them if essential. Fill up the tub and also check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at the very least when as this will settle it right into its last setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am just very drawn to A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated my page. If you appreciated our blog posting plz be sure to share it. Thanks a lot for going through it.

Get Offer